Grab N Go 406

1) Provide an additional handwash sink that is within 25 feet and easily visible from the ice machine area. Recommend installing an additional sink on the same wall as the current handwash sink that will meet the requirements. 2) Provide a 50 gallon capacity water heater unit minimum. 3) Provide a test report for the RP backflow preventer installed for the soda carbonator. 4) Provide a 1" minimum air gap above the floor sink flood rim for the ice machine drain. 5) Provide ASSE 1055 internal air gaps to the chemical dispenser units. Observed flex gaps. 6) Install ASSE 1022 dual check backflow preventers for each non-carbonated beverage machine. 7) Provide a longer swing faucet at the three sink that will reach all compartments. :

1) Provide new floor sink grates to replace any rusted or corroded floor sink grates. 2) Provide a more cleanable cover for the grease interceptor. Recommend a diamond plate sheet. 3) Replace the damaged and missing washable ceiling tiles in the back storage room. 4) Refinish the concrete floor located under the three compartment sink with new concrete sealer. 5) Provide a 3/8 inch metal cove base to the exterior of the walk-in cooler unit. 13) Reattach the existing rubber cove base in the back room to the walls, as needed. 6) Replace the missing tile cove base at the millwork junctures of the front service areas. 7)Caulk-in all plumbing penetrations and escutcheon plates with silicone. 8) Provide new black foam insulation at the walk-in cooler condenser lines. 9) Provide missing clean out covers in the restroom. 10) Fill all wall holes throughout the facility with silicone. 11) Provide the missing ceiling cover in the restroom. 12) Remove all unused items and equipment located in the facility and outside of the facility. 13) Repair or provide additional lighting in the back storage room to ensure 20 foot candles minimum is provided the area. 14) Re-caulk the sinks to the walls with new silicone, as needed :

Priority Foundation-5-203.11, Pf: Handwashing Sinks-Numbers and Capacities. For a permanent fix to this violation, check out these simple tools in our Active Managerial Control Toolbox, made especially for you. https://www.maricopa.gov/4573/AMC-Toolbox---Handwashing. ---------- Provide an additional handwash sink that is within 25 feet and easily visible from the ice machine area. Recommend installing an additional sink on the same wall as the current handwash sink that will meet the requirements. Priority Foundation-6-301.12, Pf: Hand Drying Provision. For a permanent fix to this violation, check out these simple tools in our Active Managerial Control Toolbox, made especially for you. https://www.maricopa.gov/4573/AMC-Toolbox---Handwashing. --------- Observed no paper towels at the back area handwash sink. Paper towels were provided at time of inspection. All handwash sinks must have a hand drying provision at all times to ensure staff can properly dry their hands. Correct By: Correct Prior To Reinspection

PRIORITY VIOLATION-3-201.11 (A-B), P: Compliance with Food Law; Approved Source. For a permanent fix to this violation, check out these simple tools in our Active Managerial Control Toolbox, made especially for you. https://www.maricopa.gov/4619/AMC-Toolbox---Approved-Source. ---------- Observed packaged red peanut products for sale on the main sales floor without labels. The manager was instructed to remove the products from the shelves until proper labels could be provided. Correct By: Corrected At Time Of Inspection

Core-6-202.15, C: Outer Openings, Protected ----------- Provide a new door sweep to the back exterior door. Correct By: Correct Prior To Next Routine Inspection

Core-4-402.11, C: Fixed Equipment, Spacing or Sealing -------- Re-caulk the sink fixtures to the walls with new silicone, as needed. Core-4-402.12, C: Fixed Equipment, Elevation or Sealing --------- Lift all bottom shelving pieces to provide a 6" minimum clearance from the floor, as needed. Correct By: Correct Prior To Next Routine Inspection

Priority Foundation-5-103.11, Pf: Capacity-Quantity and Availability --------- Observed a 30 gallon capacity water heater unit. Provide a 50 gallon capacity water heater unit minimum. Correct By: Correct Prior To Reinspection

Core-5-205.15 (B), C: System Maintained in Good Repair; Maintained --------- Correct the following items: 1) Provide a test report for the RP backflow preventer installed for the soda carbonator. 2) Provide a 1" minimum air gap above the floor sink flood rim for the ice machine drain. 3) Provide ASSE 1055 internal air gaps to the chemical dispenser units. Observed flex gaps. 4) Install ASSE 1022 dual check backflow preventers for each non-carbonated beverage machine. 5) Provide a hose bib vacuum breaker for the hose bib located at the exterior of the facility. 6) Repair the leak at the front service handwash sink drain line. 7) Provide a longer swing faucet at the three sink that will reach all compartments. Core-5-202.11 (B), C: Cleanable Fixtures -------- Correct the following: 1) Provide new floor sink grates to replace any rusted or corroded floor sink grates. 2) Provide a more cleanable cover for the grease interceptor. Recommend a diamond plate sheet. Correct By: Correct Prior To Next Routine Inspection

Core-6-201.11, C: Floors, Walls and Ceilings-Cleanability --------- Correct the following: 1) Replace the damaged and missing washable ceiling tiles in the back storage room. 2) Refinish the concrete floor located under the three compartment sink with new concrete sealer. Core-6-201.13, C: Floor and Wall Junctures, Coved, and Enclosed or Sealed ----------- Correct the following: 1) Provide a 3/8 inch metal cove base to the exterior of the walk-in cooler unit. 2) Reattach the existing rubber cove base in the back room to the walls, as needed. 3) Replace the missing tile cove base at the millwork junctures of the front service areas. Core-6-501.11, C: Repairing-Premises, Structures, Attachments, and Fixtures-Methods ------- Correct the following: 1) Caulk-in all plumbing penetrations and escutcheon plates with silicone. 2) Provide new black foam insulation at the walk-in cooler condenser lines. 3) Provide missing clean out covers in the restroom. 4) Fill all wall holes throughout the facility with silicone. 5) Provide a missing ceiling cover in the restroom. Core-6-501.114, C: Maintaining Premises, Unnecessary Items and Litter --------- Remove all unused items and equipment located in the facility and outside of the facility. Correct By: Correct Prior To Next Routine Inspection

Core-6-303.11, C: Intensity-Lighting -------- Repair or provide additional lighting in the back storage room to ensure 20 foot candles minimum is provided the area. Correct By: Correct Prior To Next Routine Inspection