Frenchie's pizza

No County legal action will result from this inspection.

ineffective visit

ineffective visit

No County legal action will result from this inspection.

OC Inspection - E&D Class 3This inspection was conducted with employees on duty.A PDF copy of this inspection report was emailed to Amy W. and Will C. at the time of this inspection.No county legal action will result from this inspection.This establishment is not participating in the award program at this time and had 0 Priority and 0 Priority Foundation violations on this inspection.This establishment has demonstrated sufficient compliance to proceed with the issuance of the permit. To complete the issuance of this permit and begin operation, the applicant must first submit payment of the permit fee to the Department’s Business Services Office. Per Chapter I, Regulation 4, of the Maricopa County Environmental Health Code, no person shall conduct an operation or an establishment for which a permit is required without holding the necessary and valid permit to do so. Payment with a credit card can be made in person, by US Mail, by or phone at 602-506-6824 Option 2. We accept cash, check, money order, credit/debit. It is the responsibility of the permit holder/owner to notify MCESD if there are contact/ billing address changes. All permit fees are nonrefundable.On July 1st, 2023, the Environmental Services Department started emailing permit card(s) and permit invoice(s) to permittees. We need a current and accurate email address on file to ensure you receive a copy of your permit card and invoice(s) upon renewal. If you are unsure whether your email address is accurate, you may: • Contact your inspector using the phone number or email on your last inspection report to review, or • Contact the Department using the email addresses below, o Envquickservicerestaurants@maricopa.gov (facilities such as fast-food) o Envfullservicerestaurants@maricopa.gov (facilities that are full-service restaurants) o Envretailgrocery@maricopa.gov (facilities like grocery stores or retail food markets) o Envspecialtyprograms@maricopa.gov (mobile food/special events/plan review) If you need to update your email address and/or other contact information, please submit an administrative change request form at the below website https://www.maricopa.gov/FormCenter/Environmental-Services-16/Administrative-Change-Request-Form-181.Award: Not Participating,Signer: Amy W.

Construction Inspection - E&D Class 3This inspection was conducted with an on site employee.A PDF copy of this inspection report was emailed to William C. at the time of this inspection.This facility is not currently in operation.No county legal action will result from this inspection.Correct the following prior to final permit approval;1. Provide a certified, drinking water safe, RPZ backflow prevention device for the water supply to the soda fountain carbonator. All piping and fittings on the downstream side of this device must be plastic or stainless steel, no copper or brass. There is currently a Caleffi Low Lead RPZ device installed. The RPZ device for the soda fountain carbonator must be lead free. Retain the funnel drain assembly beneath the vent of the new RPZ device that empties into the nearby floor sink with a hard pipe drain pipe.Award: Not Participating,Review Complete: CHECKED,Review Notes: QA ML,Signer: 0

Construction Inspection - E&D Class 3This inspection was conducted with the owner.A PDF copy of this inspection report was emailed to William C. at the time of this inspection.This facility is not currently in operation.No county legal action will result from this inspection.Correct the following prior to final permit approval;1. Provide a certified, drinking water safe, RPZ backflow prevention device for the water supply to the soda fountain carbonator. All piping and fittings on the downstream side of this device must be plastic or stainless steel, no copper or brass. There is currently a double check valve assembly device installed, not an RPZ device. This device must also have a funnel drain assembly beneath the vent that empties into the nearby floor sink with a hard pipe drain pipe.2. Repair the very low hot water pressure at the front hand sink.3. There is an open sewer pipe behind the soda fountain. Properly cap off an seal this sewer pipe with a proper metal or plastic screw on cap.4. The condensate from the walk-in refrigerator is now draining into a flex line end piece. Replace the flex line with hard pipe such as PVC or metal.5. Properly repair the hole in the wall around the pizza oven gas pipe near the walk-in refrigerator with a metal or FRP patch that is sealed around the pipe. Do not use plastic and caulk as was the case.6. Remove the unused water line on the wall to the right and above the front hand sink.

OC Advisory - E&D Class 3This inspection was conducted with the owner.A PDF copy of this inspection report was emailed to William C. at the time of this inspection.This facility is not currently in operation.No county legal action will result from this inspection.Correct the following prior to final permit approval;1. The front hand sink does not have hot water available and the back hand sink only has very hot water available. Repair both hand sinks to have hot and cold water available or tempered water of 100°F-108°F.2. Repair the leaking drain pipe in the front hand sink.3. The old soda fountain must be removed or properly connected with a certified, RPZ backflow prevention device and separate drain pipes for the ice bin and soda waste that each empty into a floor sink with minimum 1 in. air-gaps.4. The two right compartments of the three compartment sink are directly connected to the sewer. These compartments must be re-piped to drain indirectly to the floor sink with a minimum 1 in. air-gap between the end of the pipe and the flood rim of the floor sink. Also, properly cap off and seal the old direct sewer connection.5. There is a floor sink inside the walk-in unit where the walk-in condensate drains. The floor sink inside the walk-in refrigerator must be plugged and sealed and the condensate drain line must be rerouted to empty into the floor sink on the outside of the unit with a a minimum 1 in. air-gap.6. The atmospheric vacuum breaker on the mop sink faucet is broken and leaking. Replace the broken and leaking atmospheric vacuum breaker on the mop sink. 7. Repair the exhaust fans in each of the restrooms.8. Remove all the tape from all of the FRP panel molding pieces. There is currently tape on almost every piece of molding between the FRP panels.9. Clean, caulk and seal the space between the mop sink basin and the wall behind it.10. Replace the broken and missing door seals for each door of the walk-in refrigerator.11. Replace any missing or broken floor tiles in the kitchen floor.